MTX Series
Ample I/O and Expansion Capability
Kết nối đầu vào/ đầu ra linh hoạt
The MTX Series feature a combination of analogue and digital. Dante and YDIF connections meaning there should always be sufficient inputs & outputs for the scale of your installation.
Overview: I/O
A closer look at the inputs and outputs of the MTX and MRX processors and provide an overview of the processing available in each one.
Khe Card SD để phát lại
Bộ xử lý dòng MTX có khả năng thiết lập tín hiệu nhập/xuất lý tưởng cho nhiều ứng dụng khác nhau: 8 kênh nhập tín hiệu mono (mic/line), 2 kênh nhập tín hiệu stereo (line) và 16 kênh nhập tín hiệu số thông qua công nghệ YDIF. Đầu ra có 8 kênh mono cấp độ line và 16 kênh số thông qua công nghệ YDIF. Các bộ xử lý dòng MTX cũng có khe cắm thẻ nhớ SD để phát nhạc MP3/WAV chứa trong thẻ nhớ. Chức năng Event Scheduler cho phép bạn phát lại những file nhạc, thông báo, bản hoà âm này - hoặc thậm chí kích hoạt các thiết bị gắn ngoài có cổng xuất tín hiệu GPI - ở thời điểm hẹn trước cũng như lấy lại các thiết lập sẵn lưu trong bộ xử lý MTX.
Easily increase system inputs and outputs.
The EXi8/Exo8 are input/output expanders for the MTX/MRX Series. EXi8 converts the analog mic/line signal to digital and transmits to the MTX via Yamaha's proprietry YDIF connection. The preamps for EXi8 can be remotely controlled from an MTX/MRX Editor.
EXo8 also connects to the system via YDIF and features 8ch of DA converters that convert the digital output to high quality analog signal.
MTX Digital Network System
Using two types of networking in MTX systems can significantly reduce installation cost and time. The combination of YDIF for shorter system connections and DANTE for larger installations can considerably improve design flexibility.
Audio Network for MTX System
Các bộ xử lý MTX có định dạng truyền âm thanh số mới YDIF; một công nghệ độc quyền của Yamaha cho ra 16 kênh audio và đồng hồ thế giới thông qua cáp Ethernet CAT5 tiêu chuẩn. YDIF có thể được sử dụng để kết nối tầng nhiều bộ xử lý dòng MTX hoặc để đưa tín hiệu audio vào amm ly dòng XMV với đường cáp rất đơn giản lên đến 30 m.
Chế độ ECO
- Max. 16ch of audio can be flowed from upper stream device to lower stream device.
Chế độ ECO
- Can be used as 8ch cascade buses specifically for MTX.
- Communication can be between multiple MTX.
Dante for MTX (MTX5-D, XMV-D only)
The MTX5-D is equipped with dual Dante ports that allow 16 channels of inputs and outputs @44.1kHZ/48kHz to be run on a redundant network. Both simple and larger, sophisticated Dante network systems can be created using MTX5-D and the Dante enabled XMV-D amplifiers.
Audinate’s Dante Network Audio Protocol has been adopted, not only in Processors and Power Amplifiers, but also in many other types of digital audio equipment such as Yamaha Digital Mixing Consoles. This makes it the perfect backbone for larger networked audio systems particularly as connections are not limited to a 30m maximum as with YDIF, but can carry audio up to 100m over CAT5e cable.
A Dante digital network handles all the audio and control data making system alterations and expansion easy. New devices can be added to the network via a single CAT5e cable and quickly configured using the MTX-MRX Editor. Dante networking provides superior system flexibility as well as plenty of capacity for future expansion.
Daisy Chain Network
When building a simple system with a small number of devices. It is recommended to use Daisy Chain.
Since Dante can transfer both control and audio signals with one cable, no network switches are required for Daisy Chain mode.
Star Network
In a star network, each device is connected to a central hub. Using a GbE-compatible network switch enables you to configure a wide-band, large-scale network.
Redundant Network
If it is necessary for higher resiliency against unexpected network problems, it is recommended to use redundant network.
Hỗ trợ cho Trình quản lý miền Dante, AES67 và Khóa thiết bị Dante
Hỗ trợ chuẩn kết nối mạng âm thanh "Trình quản lý miền Dante" (cập nhật lên phiên bản 3.31). Hiện đã hỗ trợ "Trình quản lý miền Dante" của Audifying Corporation. "Trình quản lý miền Dante" của Audifying Corporation là phần mềm quản trị mạng cung cấp tính năng xác thực thông tin người dùng và cài đặt bảo mật dựa trên vai trò người điều chỉnh. Giờ đây bạn có thể xây dựng một hệ thống âm thanh an toàn và có thể mở rộng dựa trên cơ sở hệ thống Dante.
Dante-enabled model of the MTX5-D signal processor now support the AES67 audio network interconnection standard. This allows connection via AES67 to audio networks such as Ravenna, Q-LAN, or Livewire, increasing the expandability of the system.
Also supported is Dante Device Lock, which prevents a third party from modifying Dante settings. This can increase system security in environments such as concert halls where an outside operator is expected to operate the system or bring in equipment.
Smart, Flexible Paging System for Large Commercial Spaces
The PGM1 paging station and PGX1 paging expander are designed to work specifically with MRX7-D or MTX5-D. They work using PoE and connect to the network via Dante. Each PGM1 can be expanded with up to two PGX1 units and up to 4 units of PGM1 can be connected to a single system.
PGM1, PGX1
Yamaha's PGM1/PGX1 are paging stations that can be used with the MTX5-D or MRX7-D. It can be networked via a Dante Network and using Power Ethernet or PoE. This video will show you how to set up the paging station to the system.
Phần mẫu
Multi-purpose hall
Room A and Room B in the system example are normally used independently for meetings, parties, or other events, and are therefore equipped with audio systems that can be operated separately. The Yamaha MTX3 is a convenient matrix processor that can accept input from multiple audio sources and microphones and route that audio to specified speaker systems. The EXi8 is handy when you want to increase the number of available microphone inputs, for example. DCP4V4S control panels installed in each room can be set up to allow remote control of microphone level and on/off switching.
When the partition is removed and the rooms are combined to form one larger space, an appropriate setup that has been pre-programmed using the MTX-MRX Editor software can be recalled via a single button, instantly setting up the system for central control.
Simple Presentation using the Dugan Auto Mixer.
Using the four Dugan channels of the MTX3 and FBS makes it possible to have a simple presentation system that does not require an operator.
When the Dugan automixer is used, the input gain on microphones being used is automatically increased, while the gain on mics not used is decreased in order to reduce ambient noise leakage. This enhances the clarity of the sound. No specialized technical knowledge or skill is required—the mic gains are adjusted automatically.
