TF-RACK Bàn trộn kỹ thuật số
TF-RACK | ||
---|---|---|
Mixing Capacity | Input Channels | 40 (32 mono + 2 stereo + 2 return) |
Aux Buses | 20 (8 mono + 6 stereo) | |
Stereo Buses | 1 | |
Sub Buses | 1 | |
Input channel functions | 8 DCA Groups | |
I/O | Inputs | 16 mic/line (XLR/TRS combo) + 1 stereo line (RCA pin) |
Outputs | 16 (8 XLR + 8 TRS phone) | |
Expansion slots | 1 (for NY64-D) | |
On-board processors | DSP | 8 Effects + 10 GEQ |
Sampling frequency rate | Internal | 48 kHz |
Tổng độ méo sóng hài | Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω, INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz) | |
Đáp tuyến tần số | +0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT | |
Mức nhiễu & Ồn | Nhiễu đầu vào tương đương | –128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter) |
Nhiễu đầu ra thặng dư | –85 dBu, ST master off (Measured with an A-Weight filter) | |
Crosstalk | –100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min. | |
Nguồn điện yêu cầu | 100–240 V 50/60 Hz | |
Năng lượng tiêu thụ | 85 W | |
Kích thước | W | 480 mm (18-7/8 in) |
H | 132 mm (5-1/4 in) | |
D | 409 mm (16-1/8 in) | |
Trọng lượng | 9.2 kg (20.3lb) | |
Phụ kiện | Quick Guide, Power Cord NUENDO LIVE (DAW Software), Rubber stoppers(4) | |
Tùy chọn | Audio Interface Card (NY-64D), Foot Switch (FC5) | |
Khác | Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C | |
Signal delay | Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz | |
General specifications | Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders | |
Dynamic range | 110 dB typ., DA Converter, 108 dB typ., INPUT to OMNI OUT, Input Gain=Min. |
Recording/ Playback
PC/Mac (USB2.0) Recording 34 tracks, Playback 34 tracks USB Storage Device Recording 2 tracks (USB hard drive/ SSD)*, Playback 2 tracks (USB hard drive/ SSD/ thumb drive) *Please note - USB thumb drives are not supported by TF for recording purposes. Please refer to this link for compatible hard drives.
Analog input characteristics
Input Terminals GAIN Load
ImpedanceFor Use With
NominalInput Level Connector balanced /
UnbalancedSensitivity*1 Nominal Max. before clip INPUT1-16 +66dB 7.5KΩ 50-600Ω Mics
or 600Ω Lines-82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)Balanced -6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V) ST IN — 10kΩ 600Ω Lines -30dBV (31.6μV) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced *1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*4. In these specifications, 0dBu = 0.775Vrms.
*5. +48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.Analog output characteristics
Output Terminals Source
ImpedanceFor Use With
NominalOutput Level Connector balanced /
UnbalancedNominal Max. before clip OMNI OUT 1-8 75Ω 600Ω Lines +4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced OMNI OUT 9-16 TRS Phone Jack *6 PHONES *5 100Ω 40Ω Phones 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced *1. 1: GND, 2: HOT, 3: COLD
*2. Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3. In these specifications, 0dBu = 0.775Vrms.
*4. All output DA converters are 24bit, 128times oversampling.
*5. The position of the level control is lowered by 16dB from the maximum.
*6. Tip: HOT, Ring: COLD, Sleeve: GNDDigital input/output specifications
Terminals Format Data length Audio Connector USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type) iPad USB — Playback: MP3 or WAV file data / Record: WAV file data USB (A type) Control I/O specifications
Terminals Format Level Connector NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45 FOOT SW — — TS Phone
Recording/Playback
*Please note - USB thumb drives are not supported by TF for recording purposes. Please refer to this link for compatible hard drives.
Analog Input Characteristics
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*4. In these specifications, 0dBu = 0.775Vrms.
*5. +48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
Analog Output Characteristics
*1. 1: GND, 2: HOT, 3: COLD
*2. Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3. In these specifications, 0dBu = 0.775Vrms.
*4. All output DA converters are 24bit, 128times oversampling.
*5. The position of the level control is lowered by 16dB from the maximum.
*6. Tip: HOT, Ring: COLD, Sleeve: GND