user_guide

mLAN Updater for 01X User Guide

Thank you for purchasing and using the Yamaha 01X Digital Mixing Studio.

This application is for updating the mLAN part of the 01X's firmware.

What's new in this update:

· This data set updates the mLAN firmware of the 01X to version "B0-519".

· This version of firmware was modified to support internal processing changes when plugging or unplugging mLAN(IEEE1394/FireWire) cable between the 01X and the computer.

· With the previous versions of the mLAN firmware of the 01X, there is no major problem in use, however this new version makes the internal processing when plugging/unplugging smoother.

Before updating:

STEP1:This updater needs you to have the "mLAN Driver and Tools (for 01X, i88X or mLAN16E)", which can be the version bundled with Yamaha 01X or the version downloaded from "http://www.mlancentral.com", to be installed and functioning correctly.

[NOTE]

This updater can be used in conjunction with any version of "mLAN Driver and Tools (for 01X, i88X or mLAN16E)", including version 1.5.3(1.5.1 for Macintosh OS 9) which accompanies this file set. It is your choice as to whether you perform the firmware updates to 01X before or after you have updated the drivers.

STEP2: Before updating the firmware, connect your Yamaha 01X to your computer (Windows XP/Macintosh) via an mLAN(IEEE1394/FireWire) cable.

[IMPORTANT NOTE]

1. Only one computer is allowed in the IEEE1394 (FireWire) network. If you are using Firewire based networking to link other computers, please disconnect them before performing this update.

2. If you have more than one 01X in your system, please disconnect the second or more units, and update each one, separately.

3. Please disconnect all cables from other IEEE1394 (FireWire) devices or switch the power to any other Firewire device connected off, before performing this update. This includes DV video cameras, hard disk drives etc.

Note: Whilst the update is in progress

1. Please don't unplug your mLAN (IEEE1394/FireWire) cable.
2. Please don't connect any other IEEE1394 (FireWire/mLAN) devices.
3. Please don't turn 01X's power off.

Procedure for update:

1. Before starting the updater, please connect the 01X and computer with mLAN (IEEE1394/FireWire) cable and turn on the 01X's power.

2. Double-click "mLAN_Updater_for_01X.exe (for Windows XP)" or "mLAN Updater for 01X (for Mac OS9)" which is located in same folder as this document.

3. On screen, the following window will open, which shows 01X and the current version of your mLAN firmware. Please note that this is different to your mLAN firmware of the 01X, which is covered by a different update. This update is concerned with the mLAN firmware chipset of the 01X.

[NOTE]
The version displayed in this dialogue box depends on your 01X.
If the version displayed is "B0-519", then no further action is needed. You may proceed to quit the updater and move to step 8.

4. After pushing the [Update] button, a confirmation dialog will be displayed. When the [OK] button is pressed, the updating of your 01X mLAN firmware will begin.

5. A Progress bar will be displayed. Updating is completed when the bar goes to the right side of the screen.

6. Then progress bar will then be closed and the application should show "Completed". At this stage push the [OK] button.

7. When looking at the updater main screen, please make sure that the version shown is now changed to "B0-519 (Updated)". If not, you should re-launch the application and start from step 1.

8. Push the [Exit] button (for Windows XP users).
Select [Quit] from the menu (for Macintosh users).

**Attention**
If you aborted or quit from the updater before it completed, please execute the procedures from the top again.

For Mac 0S X users

You need not update the firmware to use with Mac OS X.

Error Messages:

· Cannot find the 01X. Please check the 01X turned on or the mLAN cable is properly connected.

>>>After rebooting the 01X or re-connecting it and/or the mLAN cable, push the [OK] button.

· Fail to update. Please reboot the 01X and update again.

>>>While updating, situations may occur such as an accidental power failure to the 01X or accidental removal of the mLAN cable.
After rebooting the 01X or re-connecting the mLAN cable, the 01X should re-appear, and you can proceed with the update by pushing the [OK] button.

· Completed. Please reboot the 01X and push OK.

>>>At the end of updating process, again you may accidentally turn off the 01X's power or remove the mLAN cable, again just proceed to reconnect the 01X and update as outlined in this document.

[NOTE]
If the 01X is not shown in the list window above, please EXIT and relaunch the "mLAN Updater for 01X".

mLAN is a trademark of Yamaha Corporation.

Product and company names mentioned in the installation guide are the property and trademarks of their respective owners.